Magnetizing Equipment

Magnetization Automation

Magnet Measuring Instruments

Magnetization Services

In new energy vehicles, wind power and other key areas, permanent magnets manufacturing process is often faced with low product yields, excessive energy consumption and production efficiency is not high industry pain points, and the huge power magnetizing equipment in the end how to overcome these problems? The following is a detailed answer to the core question:

1. The pass rate of traditional magnetizing equipment is less than 80%, how can JiuJu equipment increase the yield rate to more than 99%?

The key lies in two core technology designs: firstly, the patented multi-pole magnet charging head, which controls the error of magnetic field uniformity within ±0.5% by superimposing silicon steel sheets with internal teeth and precisely wound copper wire poles; and secondly, the Hall sensor array embedded in the center of the coil, which is capable of detecting air-gap magnetic field deviation at the 0.01 mm level within 50 microseconds and adjusting the pulse parameters in real time. Coupled with the automated assembly system, the magnet positioning deviation can be controlled within 0.01 mm. For example, in the production process of a high-end car audio speaker, it is relying on this combination of technologies to increase the product qualification rate from 75% of traditional equipment to more than 99%.

2. Traditional magnetizers have high energy consumption and require a water cooling system, how does JiuJi equipment reduce energy consumption?

JiuJu Capacitive High Voltage Magnetizer is equipped with an energy recovery circuit, which utilizes a diode to form a closed-loop system with the continuous-current coil, converting the reverse electromotive force generated by the magnetizing coil into reusable electric energy, directly reducing the power consumption of the equipment by 601TP3 T. At the same time, the equipment does not require the water cooling system necessary for traditional equipment, and it can realize continuous operation for 24 hours only through the inward flow of air-cooling. According to the annual output of 1 million pieces of magnets to calculate, a single device can save more than 120,000 yuan of electricity per year, truly realizing the dual objectives of energy saving and cost reduction.

3. The daily capacity of traditional equipment is less than 1,000 pieces, how can JiuJi equipment achieve a significant increase in production capacity?

This is due to the dual strategy of "precise control + parallel design": on the one hand, it adopts the multi-stage magnetic field superposition technology, with the outer coil providing the basic magnetic field and the inner coil superposing the instantaneous peak, which enables the conversion from demagnetization to 10T-class strong magnetization in just 0.01 seconds; on the other hand, it adopts the dual charging table design, so that a single machine can carry out the internal and external magnetization operations at the same time. On the other hand, with the dual charging table design, one machine can carry out both internal and external magnetization at the same time, with a production capacity equivalent to 4-6 sets of ordinary machines. Combined with the visual identification and robotic arm automated assembly system, the daily capacity of a single machine can reach more than 5,000 pieces, which is 5 times higher than the capacity of traditional machines.

4. What is the core of JiuJu's "one-stop solution" and can it be adapted to different application scenarios?

This is due to the dual strategy of "precise control + parallel design": on the one hand, it adopts the multi-stage magnetic field superposition technology, with the outer coil providing the basic magnetic field and the inner coil superposing the instantaneous peak, which enables the conversion from demagnetization to 10T-class strong magnetization in just 0.01 seconds; on the other hand, it adopts the dual charging table design, so that a single machine can carry out the internal and external magnetization operations at the same time. On the other hand, with the dual charging table design, one machine can carry out both internal and external magnetization at the same time, with a production capacity equivalent to 4-6 sets of ordinary machines. Combined with the visual identification and robotic arm automated assembly system, the daily capacity of a single machine can reach more than 5,000 pieces, which is 5 times higher than the capacity of traditional machines.

Magnetization of Magnetic Materials

3C Electronic Magnetization

Motor Rotor Magnetization

Car Speaker Magnetization

New Energy Vehicle Industry

Medical Equipment Industry

JiuJu Magnetic Stripe Magnetization Video Case: Medical Magnetic Stripe Magnetization

January 7, 2026

Automated Magnetic Charging Integrated Solution Magnetic Charging Equipment Magnetic Charging Automation Magnetic Measuring Instruments Magnetic Charging Services Magnetic stripes are widely used in medical cards, medical insurance cards and other medical credentials to store key data such as basic patient information and medical insurance participation information. Due to the frequency of use and the external environment, the magnetic stripe may become magnetically weakened or demagnetized, resulting in the inability of the equipment to read the information, and then need to be magnetized. The core principle of magnetization is to make the magnetic strip inside the...

JiuJu Magnetizing Video Case: Rubber Silicone and NdFeB Magnetizing

January 6, 2026

Automated Magnetic Charging Integrated Solution Magnetic Charging Equipment Magnetic Charging Automation Magnetic Measuring Instruments Magnetic Charging Service This paper focuses on the core process of magnetization of Rubber Silicone and NdFeB, the initial state of non-magnetic before magnetization, and the magnetic performance after magnetization. Through the gaussmeter measurement verification, it is clear that the highest magnetic unit after magnetization is up to 45.9 units and the highest magnetic unit after magnetization is up to 45.9 units (measured by gaussmeter). The magnetization process is the core link to realize the magnetic transformation of the two...

Precision Magnetization for Ferrite Cubes

November 13, 2025

Specializing in ferrite cube micro-magnetization, we deliver customized, precise solutions tailored to ferrite cube material properties. By fine-tuning parameters, we ensure the magnetization meets exact standards, fulfilling high-precision magnetic requirements and adapting to applications with strict demands for magnetization accuracy.

NdFeB Magnet Magnetization Guide – JIUJU Shows How to Select a Magnetizer

November 11, 2025

Key Points for Selecting NdFeB Magnet Magnetizers – JIUJU Professional Magnetization Solutions, Pulse Magnetizer Specifications, Equipment for High-Coercivity Materials, and Selection of Magnetizers for Permanent Magnetic Materials

JiuJu Magnetism Industry News] Preparation method of LaCoO3 chalcogenide material and its catalytic degradation effect on formaldehyde wastewater

January 9, 2026

Automated Magnetic Charging Integrated Solution Magnetic Charging Equipment Magnetic Charging Automation Magnetic Measuring Instruments Magnetic Charging Service Formaldehyde (HCHO) is a widely-existing water-soluble toxic pollutant, which mainly originates from industrial production emissions, volatilization of construction and decoration materials, and release of daily necessities. This compound is strongly carcinogenic and biotoxic, which will not only cause serious damage to the human respiratory system and immune system, but also destroy the ecological balance of the water body. Therefore, ...

JiuJu Magnetic Stripe Magnetization Video Case: Medical Magnetic Stripe Magnetization

January 7, 2026

Automated Magnetic Charging Integrated Solution Magnetic Charging Equipment Magnetic Charging Automation Magnetic Measuring Instruments Magnetic Charging Services Magnetic stripes are widely used in medical cards, medical insurance cards and other medical credentials to store key data such as basic patient information and medical insurance participation information. Due to the frequency of use and the external environment, the magnetic stripe may become magnetically weakened or demagnetized, resulting in the inability of the equipment to read the information, and then need to be magnetized. The core principle of magnetization is to make the magnetic strip inside the...

JiuJu Magnetizing Video Case: Rubber Silicone and NdFeB Magnetizing

January 6, 2026

Automated Magnetic Charging Integrated Solution Magnetic Charging Equipment Magnetic Charging Automation Magnetic Measuring Instruments Magnetic Charging Service This paper focuses on the core process of magnetization of Rubber Silicone and NdFeB, the initial state of non-magnetic before magnetization, and the magnetic performance after magnetization. Through the gaussmeter measurement verification, it is clear that the highest magnetic unit after magnetization is up to 45.9 units and the highest magnetic unit after magnetization is up to 45.9 units (measured by gaussmeter). The magnetization process is the core link to realize the magnetic transformation of the two...

JiuJi Magnetizing Video Case: Hardware Impeller Magnetizing Process and Applicable Scenarios

January 5, 2026

Automated Magnetic Charging Integrated Solution Magnetic Charging Equipment Magnetic Charging Automation Magnetic Measuring Instruments Magnetic Charging Service Hardware Impeller Magnetization is the technical process of magnetizing the impeller made of hardware by means of special magnetic charging equipment, the core purpose of which is to endow the impeller with a specific magnetism to meet the functional requirements of mechanical equipment such as motors, pumps, fans, and so on, under such scenarios as transmission, The core purpose is to give the impeller specific magnetic properties to meet the functional requirements of mechanical equipment such as motors, pumps, fans, etc. in driving, adsorption, positioning, etc. The process is based on the material of the impeller (e.g. iron, steel, alloy, etc.), the structural dimensions and the required magnetization...

JiuJu Magnetism Industry News] Preparation method of LaCoO3 chalcogenide material and its catalytic degradation effect on formaldehyde wastewater

January 9, 2026

Automated Magnetic Charging Integrated Solution Magnetic Charging Equipment Magnetic Charging Automation Magnetic Measuring Instruments Magnetic Charging Service Formaldehyde (HCHO) is a widely-existing water-soluble toxic pollutant, which mainly originates from industrial production emissions, volatilization of construction and decoration materials, and release of daily necessities. This compound is strongly carcinogenic and biotoxic, which will not only cause serious damage to the human respiratory system and immune system, but also destroy the ecological balance of the water body. Therefore, ...

JiuJu Magnetic Stripe Magnetization Video Case: Medical Magnetic Stripe Magnetization

January 7, 2026

Automated Magnetic Charging Integrated Solution Magnetic Charging Equipment Magnetic Charging Automation Magnetic Measuring Instruments Magnetic Charging Services Magnetic stripes are widely used in medical cards, medical insurance cards and other medical credentials to store key data such as basic patient information and medical insurance participation information. Due to the frequency of use and the external environment, the magnetic stripe may become magnetically weakened or demagnetized, resulting in the inability of the equipment to read the information, and then need to be magnetized. The core principle of magnetization is to make the magnetic strip inside the...

JiuJu Magnetizing Video Case: Rubber Silicone and NdFeB Magnetizing

January 6, 2026

Automated Magnetic Charging Integrated Solution Magnetic Charging Equipment Magnetic Charging Automation Magnetic Measuring Instruments Magnetic Charging Service This paper focuses on the core process of magnetization of Rubber Silicone and NdFeB, the initial state of non-magnetic before magnetization, and the magnetic performance after magnetization. Through the gaussmeter measurement verification, it is clear that the highest magnetic unit after magnetization is up to 45.9 units and the highest magnetic unit after magnetization is up to 45.9 units (measured by gaussmeter). The magnetization process is the core link to realize the magnetic transformation of the two...

JiuJi Magnetizing Video Case: Hardware Impeller Magnetizing Process and Applicable Scenarios

January 5, 2026

Automated Magnetic Charging Integrated Solution Magnetic Charging Equipment Magnetic Charging Automation Magnetic Measuring Instruments Magnetic Charging Service Hardware Impeller Magnetization is the technical process of magnetizing the impeller made of hardware by means of special magnetic charging equipment, the core purpose of which is to endow the impeller with a specific magnetism to meet the functional requirements of mechanical equipment such as motors, pumps, fans, and so on, under such scenarios as transmission, The core purpose is to give the impeller specific magnetic properties to meet the functional requirements of mechanical equipment such as motors, pumps, fans, etc. in driving, adsorption, positioning, etc. The process is based on the material of the impeller (e.g. iron, steel, alloy, etc.), the structural dimensions and the required magnetization...

JiuJu Magnetism Industry News] Preparation method of LaCoO3 chalcogenide material and its catalytic degradation effect on formaldehyde wastewater

January 9, 2026

Automated Magnetic Charging Integrated Solution Magnetic Charging Equipment Magnetic Charging Automation Magnetic Measuring Instruments Magnetic Charging Service Formaldehyde (HCHO) is a widely-existing water-soluble toxic pollutant, which mainly originates from industrial production emissions, volatilization of construction and decoration materials, and release of daily necessities. This compound is strongly carcinogenic and biotoxic, which will not only cause serious damage to the human respiratory system and immune system, but also destroy the ecological balance of the water body. Therefore, ...

JiuJu Magnetic Stripe Magnetization Video Case: Medical Magnetic Stripe Magnetization

January 7, 2026

Automated Magnetic Charging Integrated Solution Magnetic Charging Equipment Magnetic Charging Automation Magnetic Measuring Instruments Magnetic Charging Services Magnetic stripes are widely used in medical cards, medical insurance cards and other medical credentials to store key data such as basic patient information and medical insurance participation information. Due to the frequency of use and the external environment, the magnetic stripe may become magnetically weakened or demagnetized, resulting in the inability of the equipment to read the information, and then need to be magnetized. The core principle of magnetization is to make the magnetic strip inside the...

JiuJu Magnetizing Video Case: Rubber Silicone and NdFeB Magnetizing

January 6, 2026

Automated Magnetic Charging Integrated Solution Magnetic Charging Equipment Magnetic Charging Automation Magnetic Measuring Instruments Magnetic Charging Service This paper focuses on the core process of magnetization of Rubber Silicone and NdFeB, the initial state of non-magnetic before magnetization, and the magnetic performance after magnetization. Through the gaussmeter measurement verification, it is clear that the highest magnetic unit after magnetization is up to 45.9 units and the highest magnetic unit after magnetization is up to 45.9 units (measured by gaussmeter). The magnetization process is the core link to realize the magnetic transformation of the two...

JiuJi Magnetizing Video Case: Hardware Impeller Magnetizing Process and Applicable Scenarios

January 5, 2026

Automated Magnetic Charging Integrated Solution Magnetic Charging Equipment Magnetic Charging Automation Magnetic Measuring Instruments Magnetic Charging Service Hardware Impeller Magnetization is the technical process of magnetizing the impeller made of hardware by means of special magnetic charging equipment, the core purpose of which is to endow the impeller with a specific magnetism to meet the functional requirements of mechanical equipment such as motors, pumps, fans, and so on, under such scenarios as transmission, The core purpose is to give the impeller specific magnetic properties to meet the functional requirements of mechanical equipment such as motors, pumps, fans, etc. in driving, adsorption, positioning, etc. The process is based on the material of the impeller (e.g. iron, steel, alloy, etc.), the structural dimensions and the required magnetization...

JiuJu Magnetism Industry News] Preparation method of LaCoO3 chalcogenide material and its catalytic degradation effect on formaldehyde wastewater

January 9, 2026

Automated Magnetic Charging Integrated Solution Magnetic Charging Equipment Magnetic Charging Automation Magnetic Measuring Instruments Magnetic Charging Service Formaldehyde (HCHO) is a widely-existing water-soluble toxic pollutant, which mainly originates from industrial production emissions, volatilization of construction and decoration materials, and release of daily necessities. This compound is strongly carcinogenic and biotoxic, which will not only cause serious damage to the human respiratory system and immune system, but also destroy the ecological balance of the water body. Therefore, ...

JiuJu Magnetic Stripe Magnetization Video Case: Medical Magnetic Stripe Magnetization

January 7, 2026

Automated Magnetic Charging Integrated Solution Magnetic Charging Equipment Magnetic Charging Automation Magnetic Measuring Instruments Magnetic Charging Services Magnetic stripes are widely used in medical cards, medical insurance cards and other medical credentials to store key data such as basic patient information and medical insurance participation information. Due to the frequency of use and the external environment, the magnetic stripe may become magnetically weakened or demagnetized, resulting in the inability of the equipment to read the information, and then need to be magnetized. The core principle of magnetization is to make the magnetic strip inside the...

JiuJu Magnetizing Video Case: Rubber Silicone and NdFeB Magnetizing

January 6, 2026

Automated Magnetic Charging Integrated Solution Magnetic Charging Equipment Magnetic Charging Automation Magnetic Measuring Instruments Magnetic Charging Service This paper focuses on the core process of magnetization of Rubber Silicone and NdFeB, the initial state of non-magnetic before magnetization, and the magnetic performance after magnetization. Through the gaussmeter measurement verification, it is clear that the highest magnetic unit after magnetization is up to 45.9 units and the highest magnetic unit after magnetization is up to 45.9 units (measured by gaussmeter). The magnetization process is the core link to realize the magnetic transformation of the two...

JiuJi Magnetizing Video Case: Hardware Impeller Magnetizing Process and Applicable Scenarios

January 5, 2026

Automated Magnetic Charging Integrated Solution Magnetic Charging Equipment Magnetic Charging Automation Magnetic Measuring Instruments Magnetic Charging Service Hardware Impeller Magnetization is the technical process of magnetizing the impeller made of hardware by means of special magnetic charging equipment, the core purpose of which is to endow the impeller with a specific magnetism to meet the functional requirements of mechanical equipment such as motors, pumps, fans, and so on, under such scenarios as transmission, The core purpose is to give the impeller specific magnetic properties to meet the functional requirements of mechanical equipment such as motors, pumps, fans, etc. in driving, adsorption, positioning, etc. The process is based on the material of the impeller (e.g. iron, steel, alloy, etc.), the structural dimensions and the required magnetization...

JiuJu Magnetism Industry News] Preparation method of LaCoO3 chalcogenide material and its catalytic degradation effect on formaldehyde wastewater

January 9, 2026

Automated Magnetic Charging Integrated Solution Magnetic Charging Equipment Magnetic Charging Automation Magnetic Measuring Instruments Magnetic Charging Service Formaldehyde (HCHO) is a widely-existing water-soluble toxic pollutant, which mainly originates from industrial production emissions, volatilization of construction and decoration materials, and release of daily necessities. This compound is strongly carcinogenic and biotoxic, which will not only cause serious damage to the human respiratory system and immune system, but also destroy the ecological balance of the water body. Therefore, ...

JiuJu Magnetic Stripe Magnetization Video Case: Medical Magnetic Stripe Magnetization

January 7, 2026

Automated Magnetic Charging Integrated Solution Magnetic Charging Equipment Magnetic Charging Automation Magnetic Measuring Instruments Magnetic Charging Services Magnetic stripes are widely used in medical cards, medical insurance cards and other medical credentials to store key data such as basic patient information and medical insurance participation information. Due to the frequency of use and the external environment, the magnetic stripe may become magnetically weakened or demagnetized, resulting in the inability of the equipment to read the information, and then need to be magnetized. The core principle of magnetization is to make the magnetic strip inside the...

JiuJu Magnetizing Video Case: Rubber Silicone and NdFeB Magnetizing

January 6, 2026

Automated Magnetic Charging Integrated Solution Magnetic Charging Equipment Magnetic Charging Automation Magnetic Measuring Instruments Magnetic Charging Service This paper focuses on the core process of magnetization of Rubber Silicone and NdFeB, the initial state of non-magnetic before magnetization, and the magnetic performance after magnetization. Through the gaussmeter measurement verification, it is clear that the highest magnetic unit after magnetization is up to 45.9 units and the highest magnetic unit after magnetization is up to 45.9 units (measured by gaussmeter). The magnetization process is the core link to realize the magnetic transformation of the two...

JiuJi Magnetizing Video Case: Hardware Impeller Magnetizing Process and Applicable Scenarios

January 5, 2026

Automated Magnetic Charging Integrated Solution Magnetic Charging Equipment Magnetic Charging Automation Magnetic Measuring Instruments Magnetic Charging Service Hardware Impeller Magnetization is the technical process of magnetizing the impeller made of hardware by means of special magnetic charging equipment, the core purpose of which is to endow the impeller with a specific magnetism to meet the functional requirements of mechanical equipment such as motors, pumps, fans, and so on, under such scenarios as transmission, The core purpose is to give the impeller specific magnetic properties to meet the functional requirements of mechanical equipment such as motors, pumps, fans, etc. in driving, adsorption, positioning, etc. The process is based on the material of the impeller (e.g. iron, steel, alloy, etc.), the structural dimensions and the required magnetization...